Re: Help, Pogogplug E02 , No LED,serial cable connected ,what next?

Bodhi,

I finally got all the lines typed in and when I try to boot from a known working Archlinux RootFS I get the following:

U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02

SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/rescueme" from usb device 0:1 (usbda1)
** File not found /rescueme
reading /rescueme.txt

** Unable to read "/rescueme.txt" from usb 0:1 **
Unknown command '‘setenv' - try 'help'
incorrect device type in ‘nand0=orion_nand’
Error initializing mtdparts!
## Error: "usb_init" not defined
Unknown command '‘setenv' - try 'help'
** Invalid boot device, use `dev[:part]' **
** Invalid boot device, use `dev[:part]' **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
incorrect device type in ‘nand0=orion_nand’
incorrect device type in ‘nand0=orion_nand’
resetting ...

Here is my printenv:

baudrate=115200
bootargs=root=/dev/nfs nfsroot=: ip=::::::off
bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset
bootdelay=5
console=‘ttyS0,115200’
ethact=egiga0
ethaddr=00:25:31:04:88:1D
force_rescue=‘0’
force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi
if_netconsole=ping $serverip
led_error=‘orange blinking’
led_exit=‘green off’
led_init=‘green blinking’
machid=dd6
mainlineLinux=‘yes’
mtdids=‘nand0=orion_nand’
mtdparts=‘mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)’
partition=‘nand0,2’
pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi
preboot=run if_netconsole start_netconsole
rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi
rescue_installed=‘0’
rescue_set_bootargs=‘setenv bootargs console=‘ttyS0,115200’ ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs ‘mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)’ €™
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi
ubifs_mtd=‘3’
ubifs_set_bootargs=‘setenv bootargs console=‘ttyS0,115200’ ubi.mtd=‘3’ root=ubi0:rootfs rootfstype=ubifs ‘mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)’ €™
usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot
usb_device=‘0:1’
usb_root=‘/dev/sda1’
usb_rootdelay=’10’
usb_rootfstype=ext3
usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done
usb_scan_1=‘usb=0:1 dev=sda1’
usb_scan_2=‘usb=1:1 dev=sdb1’
usb_scan_3=‘usb=2:1 dev=sdc1’
usb_scan_4=‘usb=3:1 dev=sdd1’
usb_scan_list=1 2 3 4
usb_set_bootargs=‘setenv bootargs console=‘ttyS0,115200’ root=‘/dev/sda1’ rootdelay=’10’ rootfstype=ext3 ‘mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)’ €™

Environment size: 2817/131068 bytes


Any idea what I didn't do correctly?

Thanks