not until now, but i have connect over serial without USB Stick.
here is the output:
I think the Problem is the original pogo Image or?
The last line:
Error: jffs2_decompress returned -5
repeated again.
When i install the Rescue System, boot the Pogo then without USB Stick correct and become a IP?
Thanks in Advance
here is the output:
U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 3 ??? 2 ??? 1 ??? 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported
** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 728
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 717
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: ??. ??. ??. ??. ??. ??. ??. ??. ??. ??. ?? done.
### JFFS2 load complete: 524288 bytes loaded to 0x800000
## Starting application at 0x00800200 ...
U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16)
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60
Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Flash: 0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB
CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD: PPV2
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 3 ??? 2 ??? 1 ??? 0
NAND read: device 0 offset 0x100000, size 0x200000
Reading data from 0x100000 -- 0% complete.
~~
Reading data from 0x2ff800 -- 100% complete.
2097152 bytes read: OK
## Booting image at 00800000 ...
Image Name: Linux-2.6.22.18
Created: 2010-10-19 23:05:02 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1979140 Bytes = 1.9 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux............................................................................................................................ done, booting the kernel.
[ 0.000000] Linux version 2.6.22.18 (bdietrich@buildman) (gcc version 4.2.1) #81 Tue Oct 19 16:05:00 PDT 2010
[ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177
[ 0.000000] Machine: Feroceon-KW
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] CPU0: D VIVT write-back cache
[ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[ 0.000000] Built 1 zonelists. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro
[ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.010000] Memory: 256MB 0MB 0MB 0MB = 256MB total
[ 0.010000] Memory: 255872KB available (3592K code, 253K data, 124K init)
[ 0.250000] Mount-cache hash table entries: 512
[ 0.250000] CPU: Testing write buffer coherency: ok
[ 0.250000] NET: Registered protocol family 16
[ 0.250000]
[ 0.250000] CPU Interface
[ 0.250000] -------------
[ 0.250000] SDRAM_CS0 ....base 00000000, size 256MB
[ 0.250000] SDRAM_CS1 ....disable
[ 0.250000] SDRAM_CS2 ....disable
[ 0.250000] SDRAM_CS3 ....disable
[ 0.250000] PEX0_MEM ....base e8000000, size 128MB
[ 0.250000] PEX0_IO ....base f2000000, size 1MB
[ 0.250000] INTER_REGS ....base f1000000, size 1MB
[ 0.250000] NFLASH_CS ....base fa000000, size 2MB
[ 0.250000] SPI_CS ....base f4000000, size 16MB
[ 0.250000] BOOT_ROM_CS ....no such
[ 0.250000] DEV_BOOTCS ....no such
[ 0.250000] CRYPT_ENG ....base f0000000, size 2MB
[ 0.250000]
[ 0.250000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21_with_rx_desc_tuned)-- SHEEVA PLUG Soc: 88F6281 A0 LE
[ 0.250000]
[ 0.250000] Detected Tclk 200000000 and SysClk 400000000
[ 0.250000] MV Buttons Device Load
[ 0.250000] Marvell USB EHCI Host controller #0: c0652600
[ 0.750000] PEX0 interface detected no Link.
[ 0.750000] PCI: bus0: Fast back to back transfers enabled
[ 0.750000] SCSI subsystem initialized
[ 0.750000] usbcore: registered new interface driver usbfs
[ 0.750000] usbcore: registered new interface driver hub
[ 0.750000] usbcore: registered new device driver usb
[ 0.750000] NET: Registered protocol family 2
[ 0.760000] Time: kw_clocksource clocksource has been installed.
[ 0.850000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.850000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.850000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.850000] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.850000] TCP reno registered
[ 0.880000] RTC has been updated!!!
[ 0.880000] RTC registered
[ 0.880000] Use the XOR engines (acceleration) for enhancing the following functions:
[ 0.880000] o RAID 5 Xor calculation
[ 0.880000] o kernel memcpy
[ 0.880000] o kenrel memzero
[ 0.880000] Number of XOR engines to use: 4
[ 0.880000] cesadev_init(c00117b0)
[ 0.880000] mvCesaInit: sessions=640, queue=64, pSram=f0000000
[ 0.880000] MV Buttons Driver Load
[ 0.880000] squashfs: version 3.3 (2007/10/31) Phillip Lougher
[ 0.880000] squashfs: LZMA suppport for slax.org by jro
[ 0.880000] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.880000] io scheduler noop registered
[ 0.880000] io scheduler anticipatory registered (default)
[ 0.900000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
[ 0.900000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 0.910000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
[ 0.920000] Loading Marvell Ethernet Driver:
[ 0.920000] o Cached descriptors in DRAM
[ 0.920000] o DRAM SW cache-coherency
[ 0.930000] o Single RX Queue support - ETH_DEF_RXQ=0
[ 0.930000] o Single TX Queue support - ETH_DEF_TXQ=0
[ 0.940000] o TCP segmentation offload enabled
[ 0.940000] o Receive checksum offload enabled
[ 0.950000] o Transmit checksum offload enabled
[ 0.950000] o Network Fast Processing (Routing) supported
[ 0.960000] o Driver ERROR statistics enabled
[ 0.960000] o Driver INFO statistics enabled
[ 0.970000] o Proc tool API enabled
[ 0.970000] o Rx descripors: q0=128
[ 0.970000] o Tx descripors: q0=532
[ 0.980000] o Loading network interface(s):
[ 0.990000] o eth0, ifindex = 1, GbE port = 0
[ 0.990000] o eth1, ifindex = 2, GbE port = 1
[ 1.000000]
[ 1.000000] mvFpRuleDb (cfdf6000): 2048 entries, 8192 bytes
[ 1.000000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
[ 1.010000] Copyright (c) 1999-2006 Intel Corporation.
[ 1.020000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
[ 1.020000] e100: Copyright(c) 1999-2006 Intel Corporation
[ 1.030000]
[ 1.030000] Warning Sata is Powered Off
[ 1.030000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
[ 1.040000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit)
[ 1.050000] Scanning device for bad blocks
[ 1.100000] Using static partition definition
[ 1.110000] Creating 4 MTD partitions on "nand_mtd":
[ 1.110000] 0x00000000-0x00100000 : "u-boot"
[ 1.120000] 0x00100000-0x00500000 : "uImage"
[ 1.120000] 0x00500000-0x02500000 : "root"
[ 1.130000] 0x02500000-0x08000000 : "data"
[ 1.130000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
[ 1.140000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
[ 1.180000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
[ 1.200000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 1.200000] usb usb1: configuration #1 chosen from 1 choice
[ 1.210000] hub 1-0:1.0: USB hub found
[ 1.210000] hub 1-0:1.0: 1 port detected
[ 1.330000] USB Universal Host Controller Interface driver v3.0
[ 1.610000] usb 1-1: new high speed USB device using ehci_marvell and address 2
[ 1.760000] usb 1-1: configuration #1 chosen from 1 choice
[ 1.760000] hub 1-1:1.0: USB hub found
[ 1.770000] hub 1-1:1.0: 4 ports detected
[ 1.880000] usbcore: registered new interface driver usblp
[ 1.880000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[ 1.890000] Initializing USB Mass Storage driver...
[ 1.890000] usbcore: registered new interface driver usb-storage
[ 1.900000] USB Mass Storage support registered.
[ 1.910000] mice: PS/2 mouse device common for all mice
[ 1.910000] i2c /dev entries driver
[ 1.910000] Linux telephony interface: v1.00
[ 1.920000] md: linear personality registered for level -1
[ 1.920000] md: raid0 personality registered for level 0
[ 1.930000] md: raid1 personality registered for level 1
[ 2.100000] raid6: int32x1 97 MB/s
[ 2.270000] raid6: int32x2 114 MB/s
[ 2.440000] raid6: int32x4 122 MB/s
[ 2.610000] raid6: int32x8 110 MB/s
[ 2.610000] raid6: using algorithm int32x4 (122 MB/s)
[ 2.610000] md: raid6 personality registered for level 6
[ 2.620000] md: raid5 personality registered for level 5
[ 2.620000] md: raid4 personality registered for level 4
[ 2.630000] raid5: measuring checksumming speed
[ 2.680000] arm4regs : 1084.000 MB/sec
[ 2.730000] 8regs : 754.800 MB/sec
[ 2.780000] 32regs : 899.600 MB/sec
[ 2.780000] raid5: using function: arm4regs (1084.000 MB/sec)
[ 2.790000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
[ 2.790000] dm_crypt using the OCF package.
[ 2.800000] sdhci: Secure Digital Host Controller Interface driver
[ 2.800000] sdhci: Copyright(c) Pierre Ossman
[ 2.810000] usbcore: registered new interface driver usbhid
[ 2.810000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 2.820000] TCP cubic registered
[ 2.820000] NET: Registered protocol family 1
[ 2.830000] NET: Registered protocol family 17
[ 2.830000] md: Autodetecting RAID arrays.
[ 2.840000] md: autorun ...
[ 2.840000] md: ... autorun DONE.
[ 4.080000] Empty flash at 0x005d03c4 ends at 0x005d0800
[ 4.540000] Empty flash at 0x009ac208 ends at 0x009ac800
[ 8.340000] VFS: Mounted root (jffs2 filesystem) readonly.
[ 8.340000] Freeing init memory: 124K
[ 8.390000] JFFS2 notice: (1) check_node_data: wrong data CRC in data node at 0x005d0000: read 0x2f0ca840, calculated 0x18036fd2.
[ 8.780000] JFFS2 compression type 0x07 not available.
[ 8.790000] Error: jffs2_decompress returned -5
[ 8.790000] JFFS2 compression type 0x07 not available.
[ 8.800000] Error: jffs2_decompress returned -5
I think the Problem is the original pogo Image or?
The last line:
Error: jffs2_decompress returned -5
repeated again.
When i install the Rescue System, boot the Pogo then without USB Stick correct and become a IP?
Thanks in Advance