Re: Pogoplug E02 Bad Block

bodhi,

Thanks for your guide from your old post. I am able to get usb to boot. It is nice to be able to use the stock OS to troubleshoot failed to boot thumb drive

1. fw_printenv output

[root@alarm ~]# fw_printenv 
ethact=egiga0
bootdelay=3
baudrate=115200
mainlineLinux=yes
console=ttyS0,115200
led_init=green blinking
led_exit=green off
led_error=orange blinking
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
mtdids=nand0=orion_nand
partition=nand0,2
stdin=serial
stdout=serial
stderr=serial
rescue_installed=0
rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params
rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi
pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi
force_rescue=0
force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi
ubifs_mtd=3
ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params
ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi
usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done
usb_scan_list=1 2 3 4
usb_scan_1=usb=0:1 dev=sda1
usb_scan_2=usb=1:1 dev=sdb1
usb_scan_3=usb=2:1 dev=sdc1
usb_scan_4=usb=3:1 dev=sdd1
usb_init=run usb_scan
usb_device=0:1
usb_root=/dev/sda1
usb_rootdelay=10
usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params
usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot
usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset
usb_rootfstype=ext3
arcNumber=3542
machid=dd6
ethaddr=00:25:31:24:50:33
serverip=192.168.1.100
ipaddr=192.168.1.101
if_netconsole=ping $serverip
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
preboot=run if_netconsole start_netconsole

2. Booted from USB Stick

[root@alarm ~]# mkdir -p /tmp/pogoroot
[root@alarm ~]# mount -t jffs2 /dev/mtdblock2 /tmp/pogoroot
mount: special device /dev/mtdblock2 does not exist

[root@alarm ~]# mknod /dev/mtdblock2 b 31 2
[root@alarm ~]# mount -t jffs2 -o rw /dev/mtdblock2 /tmp/pogoroot/
[root@alarm ~]# cat /tmp/pogoroot/etc/init.d/rcS 
#! /bin/sh

mount -t proc none /proc
mount -t sysfs none /sys
mount -t devpts none /dev/pts
mount -t tmpfs none /tmp
mkdir /tmp/var

echo "/tmp/core_%e_%t" > /proc/sys/kernel/core_pattern

hostname Pogoplug

ifconfig lo 127.0.0.1
ifconfig eth0 169.254.37.133
udhcpc -b `hostname`

#telnetd
/etc/init.d/db

/etc/init.d/hbmgr.sh start

#/bin/mount -a
[root@alarm ~]#