The serial cable arrived and this is the output during bootup from putty:
U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported
** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 728
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 717
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
NAND read: device 0 offset 0x100000, size 0x400000
4194304 bytes read: OK
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-2.6.32.18-dockstar
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3236180 Bytes = 3.1 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Using machid 0xdd6 from environment
Starting kernel ...
Uncompressing Linux............................................................................................................................................................................................................. done, booting the kernel.
Error: unrecognized/unsupported machine ID (r1 = 0x00000dd6).
Available machine support:
ID (hex) NAME
00000690 Marvell DB-88F6281-BP Development Board
00000691 Marvell RD-88F6192-NAS Development Board
00000692 Marvell RD-88F6281 Reference Board
0000078c Marvell 88F6281 GTW GE Board
00000831 Marvell SheevaPlug Reference Board
00000bb6 Seagate FreeAgent DockStar
00000c11 Seagate Goflex Net
0000085b QNAP TS-119/TS-219
00000915 Marvell OpenRD Base Board
Please check your kernel config and/or bootloader.
It looks like I have the wrong machine ID but I am not sure how to send a command via putty to fix it. I have tried googling it but no joy yet. When I plug it in to a router I don't get a IP address. Thanks for your help bohdi.
-radsfaninlv
U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported
** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 728
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 717
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
NAND read: device 0 offset 0x100000, size 0x400000
4194304 bytes read: OK
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-2.6.32.18-dockstar
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3236180 Bytes = 3.1 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Using machid 0xdd6 from environment
Starting kernel ...
Uncompressing Linux............................................................................................................................................................................................................. done, booting the kernel.
Error: unrecognized/unsupported machine ID (r1 = 0x00000dd6).
Available machine support:
ID (hex) NAME
00000690 Marvell DB-88F6281-BP Development Board
00000691 Marvell RD-88F6192-NAS Development Board
00000692 Marvell RD-88F6281 Reference Board
0000078c Marvell 88F6281 GTW GE Board
00000831 Marvell SheevaPlug Reference Board
00000bb6 Seagate FreeAgent DockStar
00000c11 Seagate Goflex Net
0000085b QNAP TS-119/TS-219
00000915 Marvell OpenRD Base Board
Please check your kernel config and/or bootloader.
It looks like I have the wrong machine ID but I am not sure how to send a command via putty to fix it. I have tried googling it but no joy yet. When I plug it in to a router I don't get a IP address. Thanks for your help bohdi.
-radsfaninlv