Re: Minimum implementation of Asterisk for Google Voice?
The new How-To can be found here.
View ArticleRe: Serial wire connector too big for JST header
> What is the good way to cut a hole through the hard plastic case of these plugs? drilling it or use soldering iron? > I would suggest a drill, but start a small tap with a knife or nail (just...
View ArticleRe: Do I need a serial cable?
The serial cable arrived and this is the output during bootup from putty: U-Boot 2011.12 (Feb 20 2012 - 21:21:59) Pogoplug E02 SoC: Kirkwood 88F6281_A0 DRAM: 256 MiB WARNING: Caches not enabled NAND:...
View ArticleRe: Do I need a serial cable?
I figured out how to get a command prompt. It helps to fully read the output. I changed the machine id to 831 and the arcNumber to 2097 but it still doen't boot. output of printenv: arcNumber=2097...
View ArticleRe: Do I need a serial cable?
radsfaninlv, A couple things to try: 1. Your uBoot envs look good, except that the machid is still set to dd6, while arcNumber is 2097. Without USB attached, try setting it again to 831 in serial...
View ArticleRe: U-Boot w/ MMC/SD-card booting for Pogoplug Series 4
Download links are dead. I have both nand and uart flashes for mobile, but I need the normal uboot. edit: oh there it is...
View ArticleDockstar cannot ping outside in native mode
Hi, I have an dockstar it's uboot has never been updated. When I try to run it with no USB attached, it can connect to my local network fine but cannot ping outside. I think it is dns server problem...
View ArticleRe: Dockstar cannot ping outside in native mode
twinclouds, Did you check /etc/resolv.conf ? try to have only Google name server in this file nameserver 8.8.8.8 Later, you might also want to kill Pogoplug process: killall -q hbwd It's been a while...
View ArticleRe: Kirkwood U-boot - Getting all supported Kirkwoods on-board
I've been thinking exactly the same. I have a handfull of Netgear Stora's, pogoplugs, NSA320 that would greatly benefit. I've been interested in FDT as well. I'm an engineer in the Networking division...
View ArticleRe: Linux Kernel 3.13.1 Kirkwood package and rootfs (Non Flattened Device Tree)
Hi there. I wanted to know if there i2s support is activated in the kernel! I want to use a I2S DAC with the goflex net. Thanks in advance
View ArticleRe: Is there a newer u-boot for Netgear Stora (RD-88F6281A LE)
Hi heychris, asuming your pendrive is formatted in ext2 or ext3, this should work :) setenv bootargs $(console) root=/dev/sda1 rootdelay=8 usb reset ext2load usb 0 0x200000 /boot/uImage ext2load usb 0...
View ArticleRe: dpf-ax: unsupported dpf - requests
@nexus Okay. I have rewritten the brightness setting. Does this work? superelchi
View ArticleRe: Yet Another ARM!
Thnx freebird, While setting up my plugs, from what I read on the various posts was that Arch was a little quick on the trigger with updates. Apparently "A little too cutting edge". So some stuff got...
View ArticleRe: dpf-ax: unsupported dpf - requests
hi again tested the new fw. now its black from 1-4 , 5 works , 6 little brighter , 7-21 no differenz thanks anyway
View ArticleRe: Dockstar cannot ping outside in native mode
Hi, Bodhi: Thank you for your prompt reply as always. The problem I found was that I am experimenting vpn for my home network. Somehow the Dockstar was signed a vpn IP address. The vpn can only...
View ArticleRe: 2013.10 U-Boot for FDT and Non-FDT Kernel - GoFlex Net/GoFlex Home/Pogo E02
Hi Bodhi et al, I have had occasional problems with the default times of dec 31 1969 when my pogo v2 boots. My current work-around is to run a script at boot that keeps checking for the network and...
View ArticleRe: Linux Kernel 3.13.1 Kirkwood package and rootfs (Non Flattened Device Tree)
bodhi - can you pls verify if hiddev is enabled in your kernel when it was compiled? i see its enabled in the config file (CONFIG_USB_HIDDEV = y) but when I plug in my UPS and run apcupsd, it cannot...
View ArticleRe: 2013.10 U-Boot for FDT and Non-FDT Kernel - GoFlex Net/GoFlex Home/Pogo E02
Klaus and TJ, I've built a new version with SNTP and DNS config options and testing it right now. ATM, I can't get out to ntp server or ping Google either. I believe I'm missing some required config...
View Article