Re: Pogoplug Mobile V4-A1-01 troubles

Here is what I got

U-Boot 1.1.4 (Oct  1 2011 - 12:21:35) Cloud Engines 1.1.2 (3.4.27) PHYADDR=0

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006918B4

Soc: 88F6192 A1 (DDR2)
CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 200Mhz , TClock = 166Mhz

DRAM CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3
DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB
Flash:  0 kB

CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD: PPV4A1

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
Unknown command 'usb' - try 'help'

NAND read: device 0 offset 0x100000, size 0x73d0c
 474380 bytes read: OK
## Starting application at 0x00800000 ...


U-Boot 1.1.4 (Jan 13 2012 - 22:33:21) Arch Linux ARM (PPV4 r1) PHYADDR=0

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CFD60

Soc: 88F6192 A1 (DDR2)
CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 200Mhz , TClock = 166Mhz

DRAM CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3
DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB
Flash:  0 kB

CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD: PPV4A1

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
(Re)start USB...
USB:   scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
T Device NOT ready
   Request Sense returned 00 00 00
1 Storage Device(s) found

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found

Device NOT ready
   Request Sense returned 00 00 00
** Can't read from device 0 **

** Unable to use usb 0:1 for fatls **

IDE device 0 not available
** Bad partition 1 **
ALARM>>


ALARM>> printenv


baudrate=115200


loads_echo=0


rootpath=/mnt/ARM_FS/


netmask=255.255.0.0


run_diag=yes


CASset=min


MALLOC_len=1


ethprime=egiga0


load_nand=nboot 0x800000 0 0x200000


load_nand2=nboot 0x800000 0 0x500000


boot=bootm 0x800000


boot_nand=run load_nand boot || run load_nand2 boot


ethmtu=1500


usb0Mode=host


nandEcc=1bit


ethact=egiga0


#ethaddr=00:24:71:04:a4:f3


#cesvcid=2FDEVMHQK25Y4DWY6QXZVVBCX


ceboardver=PPV4A1


ipaddr=192.168.58.233


serverip=192.168.58.188


bootargs=console=ttyS0,115200 root=ubi0:rootfs ubi.mtd=4,2048 rootfstype=ubifs


arcNumber=3960


bootcmd=if usb start; then run alarm_boot; else nand read 0x800000 0x100000 0x73d0c; go 0x800000; fi


alarm_boot=ide reset; run alarm_revert; if ide part 0; then run alarm_ide; else setenv isDisk no; fi; run alarm_usb


alarm_revert=if fatls usb 0:1 /revert; then setenv mainlineLinux no; setenv arcNumber; setenv bootcmd run boot_nand; saveenv; reset; fi


alarm_args=setenv bootargs console=ttyS0,115200 root=$device rootwait rootfstype=ext3


alarm_which=if test $isDisk = yes; then setenv device /dev/sdb1; else setenv device /dev/sda1; fi


alarm_ide=if ext2load ide 0:1 0x800000 /boot/uImage; then setenv device /dev/sda1; run alarm_args; bootm 0x800000; else setenv isDisk yes; fi


alarm_usb=if ext2load usb 0:1 0x800000 /boot/uImage; then run alarm_which; run alarm_args; bootm 0x800000; fi


stdin=serial


stdout=serial


stderr=serial


mainlineLinux=yes


enaMonExt=no


enaCpuStream=no


enaWrAllo=no


pexMode=RC


disL2Cache=no


setL2CacheWT=yes


disL2Prefetch=yes


enaICPref=yes


enaDCPref=yes


sata_dma_mode=yes


netbsd_en=no


vxworks_en=no


bootdelay=1


disaMvPnp=no


hddPowerCtrl=no


pcieTune=no


isDisk=no





Environment size: 1627/131068 bytes


ALARM>>

# I added the # and changed that info as I pasted here, not sure if that info needs to be kept private.
Thanks for the help!!