Re: Newer uBoot as workaround to 3.2 kernel problem?
What is the latest version of u-boot for a Seagate Dockstar and GoFLEX NET? Where can I download them?
View ArticleRe: Boot your Dockstar by TFTP/NFS
qdftowner, Thanks for the info. But strange, "vers=3" did not work for me, the kernel rejected it as an option in the command line. I'm running 3.8.11. When I use v3, it was accepted.
View ArticleRe: Problem with two SATA drives on GoFlex Net
You could try this kernel: http://forum.doozan.com/read.php?2,12096 I don't have 2 SATA disks plugged in to do the test, so not sure if the sata_mv patch will fix this problem.
View ArticleRe: A10 Rescue System
Is there any chance that this rescue system would also work on a A13b SOC ? Is there support for a usb ethernet dongle (rtl8150) ? as the fbcon will most likely not work on the A13b. Regards David
View ArticleRe: Problem with two SATA drives on GoFlex Net
I installed that kernel yesterday but the problem is still there. Is there a topic for howto check out the source for the kernel anywhere on this forum?
View ArticleRe: Linux 3.3.2 kernel for Dockstar, GoFlex and many others
Hi again, I got my serial cable, here is the output of a 3.8.4 kernel: ......... [ 30.989456] md: ... autorun DONE. [ 30.992888] VFS: Cannot open root device "LABEL=rootfs" or unknown-block(0,0):...
View ArticleRe: Newer uBoot as workaround to 3.2 kernel problem?
Thank you. But, that doesn't seem to support SATA on a GoFLEX NET device, or does it?
View ArticleRe: Newer uBoot as workaround to 3.2 kernel problem?
habibie Wrote: ------------------------------------------------------- > Thank you. But, that doesn't seem to support SATA > on a GoFLEX NET device, or does it? It does. Use the right SATA port.
View ArticleRe: Serial wire connector too big for JST header
Syong, > http://www.ebay.com/itm/350540353534?ssPageName=ST > RK:MEWNX:IT&_trksid=p3984.m1497.l2649 So with this, you just get an headphone audio cable, open one end and connect the wires to...
View ArticleRe: Rescue System
QuoteThis is a bootable image for the A10 systems. When this image is written to an empty flash card, it will use the first 32MB of the card for uBoot and a 31MB FAT32 partition (I'll refer to this as...
View ArticleRe: Linux Kernel 3.8.11 Kirkwood package and rootfs (Non Flattened Device Tree)
@chessplayer, > On the Zyxel, > things seem a bit different, but since I do not > have time and you do not have the machine, I can > very well live with the way things are. Did kernel...
View ArticleRe: Usb Connect error - Failed to claim usb device!
thanks for the reply. I had the same suspicion, but accoroding to the list of installed packages, "gettext-base" was installed. Or is there a difference between "gettext" and "gettext-base"?
View ArticleInstall debian from resuce v2: perl conflict
Hi, I had a usb-stick going bad and now have to reinstall debian on my pogoplug v2. I have the rescue system v2 installed, but following the instructions from here http://projects.doozan.com/debian/ I...
View ArticleRe: Problem with two SATA drives on GoFlex Net
xpress Wrote: ------------------------------------------------------- > I installed that kernel yesterday but the problem > is still there. I had tried this with the 2nd SATA disk, and this...
View Articlehowto write uboot to nand
I thought I should ask before I screw this up. I have a new uboot that I load with kwboot. It works fine and I want to write it to nand. I see many references to write it after loading with tftp but...
View ArticleRe: Problem with two SATA drives on GoFlex Net
I only discovered it because I want my raid setup based on the ports, so I can swap out a drive when (not if) it brakes and hopefully the raid will recover once a new drive has been inserted.
View Article