Re: installing debian on iomega iconnect
fonsty Wrote: ------------------------------------------------------- > 2. how to setup torrent client (is it possible > start downloading from work place over internet), As bodhi said,...
View ArticleRe: MacPlug & SMBPLug : Mac/AFPD or Windows/SMB + Print services in a...
I compiled usb_printid on my nsa320 ajnd copied it to mymacplug. I put it in temp directory and changed permissions but says its not there when I type. /USB_printerid / dev USB/lp0. Tried other ways...
View ArticleRe: How dead is dead? No response from bus pirate jtag(s).
Yes, I ordered a taio parport wiggler and had success with that. It was problematic but to make a long story short it was all my fault. I did learn a lot and I am presently trying to get Davygravy's...
View ArticleRe: Serial Port connector - what are people using to make it work?
The parts you pointed me to arrived last week and the serial console on my test Pogo is working great. Thanks again, bodhi. One question: What is the "RST" pin on the USB-to-TTL interface? I've heard...
View ArticleRe: Serial Port connector - what are people using to make it work?
Restamp, Glad you got it working to your satisfacory! I don't know what RST pin does either, I never tried it. I think it is the RESET signal for the controller chip.
View ArticleRe: Tip: Use wire wrap terminals to connect serial cable
@PhantomsDad, Thanks for the info! I'd never know such alternative for soldering even exists. One of the plugs I have, instead of just holes, they are filled with solder. I suppose I would need to...
View ArticleRe: Zyxel NSA320 : basic support for Debian installation
I think the major differences are 1.6GHz vs 1.2GHz CPU and a USB3 port. I seem to recall some indication that there may be other less visible differences, like the system management chip.
View ArticleCan't install uboot on Black e02
Whenever I follow the standard steps to install uboot (http://archlinuxarm.org/platforms/armv5/pogoplug-v2-pinkgray#qt-platform_tabs-ui-tabs2) I get the following: # Validating existing uBoot... Block...
View ArticleRe: Tip: Use wire wrap terminals to connect serial cable
If you find the header with the correct ptich (I did on a old hard drive), you can also use old sound card to CDROM cables, they have a matching female connector.
View ArticleRe: GoFlex NET: SATA disk not visible
Booting is not the main problem because I can set priority to boot from SATA disk. The main problem is that the harddisks behind the USB Hub are not working stable. With the Pogoplug Pro this is...
View ArticleRe: Can't install uboot on Black e02
./install_uboot_mtd0.sh: line 82: wget: command not found ./install_uboot_mtd0.sh: line 85: wget: command not found Maybe try this. Edit the install script to change all "wget" to "busybox wget"
View ArticleRe: GoFlex NET: SATA disk not visible
shv, You could try UART booting with this new uBoot image before changing anything. It could be uBoot driver problem, or perhaps uBoot envs need to be adjusted. http://forum.doozan.com/read.php?3,12381
View ArticleRe: Replace Ubit v0.5 with Uboot and a good kernel for GoFlex Net
bodhi Wrote: ------------------------------------------------------- > Too bad you don't have another plug (e.g Pogoplug > V2, Mobile,...) , if you do then I can provide you > with the kwboot...
View ArticleRe: GoFlex NET: SATA disk not visible
I tried UART booting but it doesn't work. Later I found out that my device has a BootROM version 1.11 so that I can't use UART booting with it.
View ArticleRe: Ok, So...I KNOW My Pogo is HOSED, here's why:
Well, I should have gotten on here, and went to aliexpress.com like some have said... I went to Banggood.com and ordered a similar product (one that uses a PL-2303HX chip) for an arduino board, and,...
View ArticleRe: Booting Debian on Pogoplug Pro
bodhi Wrote: ------------------------------------------------------- > @sxk, > > I guess it > > is not even coming to sysvinit. > > > > I think you're right, the LED...
View ArticleRe: Replace Ubit v0.5 with Uboot and a good kernel for GoFlex Net
Ah! yours is the first GoFlex Net that I've seen reported the BootROM 1.1.1. Must be of older lots of production. I guess to update uBoot, you just need to use the image that has been proven to work....
View ArticleRe: Booting Debian on Pogoplug Pro
mk2k, If the LED is solid green, it means uBoot has done booting the uImage. But for some reason the the rootfs did not loaded correctly. If you can find Debian rootfs with kernel 2.6.3x, you can put...
View ArticleRe: Ok, So...I KNOW My Pogo is HOSED, here's why:
Kapt Blasto Wrote: ------------------------------------------------------- > Well, I should have gotten on here, and went to > aliexpress.com like some have said... > > I went to...
View Article